Best Methods for Cutting Metal

Grinder cutting metal rebar | Construction Pro Tips
Family Handyman

1 / 9

Easy ways to cut metal fast

There’s nothing wrong with using a good, old-fashioned hacksaw, but there are faster, easier ways to cut metal. In this story, we’ll show you power tool tips and techniques for cutting the types and thicknesses of metal that you’re going to handle the most.

Diamond grinding disc | Construction Pro Tips
Family Handyman

2 / 9

What's the best cutting disk for metal?

An angle grinder fitted with an abrasive metal-cutting disc works well to cut all kinds of metal, including bolts, angle iron, rebar and even sheet metal. But the discs wear down quickly, cut slowly and shrink in diameter as you use them. Instead, we recommend using a diamond blade that’s rated to cut ferrous metal. These will last much longer, cut faster and cleaner, and wear down much slower than abrasive discs. You’ll find ferrous-metal-cutting diamond blades for $13 to $40 at home centers, hardware stores and online.

Circular saw cutting metal roofing | Construction Pro Tips
Family Handyman

3 / 9

Best way to cut sheet metal

It may not be an obvious choice, but fitted with the right blade, a circular saw is a great metal-cutting tool. In our test, it cut through rebar like a hot knife through butter. You can cut mild steel up to about 3/8 in. thick using a ferrous-metal-cutting blade. Be careful, though! Hot metal chips will fly everywhere. Put on your safety gear, keep bystanders away, and cover anything you don’t want coated with metal chips. You’ll find ferrous-metal-cutting blades at home centers, hardware stores and online. There are two types: inexpensive steel-tooth blades and carbide-tooth blades ($8 to $40). Carbide-tooth blades are more expensive but will last longer.

Using wood to hold down metal for cutting on a miter saw | Construction Pro Tips
Family Handyman

4 / 9

Cut aluminum with your miter saw

Making accurate cuts on aluminum rods, tubes and angles is easy with a miter saw and a blade designed to cut nonferrous metal (check the label). If the motor housing on your saw is open and could collect metal chips, tape a piece of cloth over the openings to protect the motor windings and bearings while you cut the aluminum. (Remember to remove it when the saw goes back into regular service or the motor will overheat.) Trapping the aluminum with a wood backer as shown reduces the danger of flying metal shards and makes it easier to hold the metal in place for cutting. This tip is especially important when you‘re cutting thin-walled pieces. Without the backing board, the blade will often catch on the metal and distort it and make it unusable. 

Cuting stainless steel with a grinding disc | Construction Pro Tips
Family Handyman

5 / 9

Cut stainless steel with a grinding disc

There are many types of stainless steel, and some hard varieties are challenging to cut. For small jobs like cutting stainless steel backsplash tiles, a rotary tool fitted with an abrasive metal-cutting disc works fine. For larger jobs, mount an abrasive disc in an angle grinder.

Scoring metal stud with a knife | Construction Pro Tips
Family Handyman

6 / 9

Simply score and snap

Siding contractors and roofers routinely score and snap aluminum siding and flashing to create straight, precise cuts. You can use the same technique anytime you need a straight cut on aluminum or other light-gauge sheet metal, even steel. Clamp or hold a straightedge or square along the cutting marks and score a line with the tip of a sharp utility knife blade. Then just bend the sheet back and forth a few times to snap it. You can use the same trick to cut steel studs. Snip the two sides. Then score a line between the cuts and bend the stud to break it.

Oscillating tool cutting pipe | Construction Pro Tips
Family Handyman

7 / 9

Get into tight spots with an oscillating tool

When access is tight, or you need to make a flush cut, an oscillating tool fitted with a metal-cutting blade will solve the problem. Corroded mounting nuts on toilets and faucets are easy to cut off with an oscillating tool. You can also use an oscillating tool to cut plumbing pipes, automotive bolts, nails and other metal objects in places where a larger tool wouldn’t fit. Just make sure the blade is intended to cut metal.

Reciprocating saw cutting a pipe | Construction Pro Tips
Family Handyman

8 / 9

Cut with a reciprocating saw

The next time you reach for your hacksaw, grab your recip saw instead. Mount a metal-cutting blade in your recip saw and you’ve got the ultimate power hacksaw for cutting bolts, rods, pipes and angle iron. A recip saw with a metal-cutting blade also works great for remodeling demolition when there are nails and pipes to cut off. Here are a few tips for cutting metal with a recip saw:

Cutting metal lath with a grinder | Construction Pro Tips
Family Handyman

9 / 9

Can a grinder cut metal?

Metal lath and hardware cloth can be cut with a tin snips, but there’s an easier way. Mount a diamond blade in your angle grinder and use it like a saw to cut the mesh. We recommend using a diamond blade that’s labeled as a ferrous-metal-cutting blade, but many tradespeople use a regular masonry diamond blade with good results.