14 Proven Drill Press Tips And Techniques

A drill press is a powerful multipurpose tool—if you learn how to get the most out of it. These tips and tricks will help you do just that.

punching a drill press into wood | Construction Pro Tips
Family Handyman

1 / 14

Get the most from your machine with DIY drill press accessories and tips

A drill press is a simple, one-job tool, right? Some might even call it “boring.” But as is often the case with tools, many tinkering minds have come up with clever ways to use this humble shop staple. Here’s how to use your drill press to its full potential.

setting up the table of a drill press | Construction Pro Tips
Family Handyman

2 / 14

Set the table for perfect “perpendicularity”

A drill press can only drill perfectly straight holes if the table is perfectly perpendicular to the spindle. Here’s an old machinist’s trick to make your table spot-on. Make about a 30-degree bend in a 1/4-in. steel rod about 2 in. from the end. Cut it to a length that will reach the outer edges of your table when the short end is in the chuck. Chuck in the rod and then turn the chuck so that the rod’s end is oriented toward either edge of the table. Raise the table until the rod just touches the surface and then lock the table. Turn the chuck to position the rod on the opposite edge of the table. Adjust the tilt of the table until the rod touches both edges equally. Lock the tilt adjustment nut and never adjust it again.

adjusting the speed on a drill press | Construction Pro Tips
Family Handyman

3 / 14

Check your speed for effective drilling

Detailed charts are available online with information about speed, bit types, diameters and the material being drilled. But here are two general rules: Decrease speed as the bit diameter increases, and slow way down for steel. Some high-end drill presses have a variable-speed dial on the front. Otherwise, you’ll change speeds by changing the belt position on the pulleys located under the top cover. On most drill presses, a graphic under the lid shows the speeds associated with different belt positions. To change the belt positions, first release the motor lock to take the tension off the belts.

adjusting belt tension in a drill press | Construction Pro Tips
Family Handyman

4 / 14

Drill press hacks: Adjust belt tension to limit vibration

After you’ve changed speeds, or if your drill press has excessive vibration, check the belt tension. You should be able to deflect the belt with your finger no more than 1/2 in. midway between pulleys. To adjust the tension, loosen the motor lock, move the motor forward or backward, and then tighten the lock again. Some drill presses have a tension adjuster lever to move the motor.

Setting the depth of a drill press | Construction Pro Tips
Family Handyman

5 / 14

No-fuss depth setting

Mark the desired depth on the edge of your workpiece. Lower the spindle until the bit reaches the mark, and then set your depth stop.

drilling into a clamped piece | Construction Pro Tips
Family Handyman

6 / 14

Make a clamp bar for small parts

To safely drill small parts, you need a way to hold them. A clamp bar is a fast solution, and a simple DIY drill press accessory. Predrill a screw hole in the end of a 1x2, and then screw it directly to the table where needed, according to the size of the workpiece. This pivoting bar lets you squeeze the workpiece against the fence while keeping your hands out of the way. For dowels, cut a V-notch in the bar to keep them from sliding. A hand screw clamp (below) also works well for small parts, again with a V-notch for dowels.

You can also use a v-block for cutting this type of material.

drilling into a clamped piece | Construction Pro Tips
Family Handyman

| Construction Pro Tips
Family Handyman

7 / 14

Add a bigger table for better support

Most drill press tables are small and not ideal for woodworking, so add a larger table. Two thicknesses of MDF will suffice. On the table shown, the top layer of MDF is assembled as a frame. This allows for a replaceable sacrificial insert where all the drilling happens. The insert is offset so that only one quadrant is centered under the chuck. This lets you use all four quadrants of the insert before it needs replacing.

Family Handyman

8 / 14

Clear debris quickly with an air nozzle

I’ve tried shop vacuums and dust collection setups on my drill press, but they’re not very effective. The best thing for clearing dust off the table and out of the bit’s flutes is compressed air. I hang an air nozzle from an eye screw on the underside of the table for one of the easiest DIY drill press accessories ever.

Family Handyman

9 / 14

Secure workpieces with toggle clamps

Sometimes—such as when you’re drilling steel—you need to firmly clamp your workpiece to the table. I use a pair of toggle clamps. I just screw them directly to the table where needed.

Family Handyman

10 / 14

Drill angled holes with a hinged table

To drill shallow angles, don’t tilt the table. Instead, make a hinged platform. Join two pieces of MDF together at one end with a piano hinge. The platform is 3 in. narrower, centered on the base. The fulcrum is 1-1/2 in. tall, and its length is the same as the platform’s width. Fasten a 1-1/2-in. angle bracket to each end of the fulcrum. To use, slide the fulcrum to create the desired angle, and then clamp or screw the angle brackets to the base.

Family Handyman

11 / 14

Make a dust channel for accurate drilling

When you’re drilling, sawdust collects between the fence and the workpiece, preventing your workpiece from registering against the fence for subsequent holes. Make a 1/4-in. x 1/4-in. rabbet on the fence’s bottom edge so the dust has a place to go and won’t interfere with drilling accuracy. Likewise, when you're clamping stops to the fence, leave them 1/4 in. above the table’s surface. Watch a video showing this trick in action here.

Family Handyman

12 / 14

Stabilize round stock with a V-Block

To drill a hole or a straight line of holes in a cylindrical object, use a shop-made V-block. To make this DIY drill press accessory, set your table saw or circular saw blade to 45 degrees, and then make two passes to create the “V.” Leave a little extra length on the dowel, screw the end of the dowel to the V-block and cut that end off later when you’re finished. A framing square also makes a great helping hand with your drill press.

Family Handyman

13 / 14

Build a sanding table in 5 minutes

A set of sanding drums is a handy addition to your drill press. One advantage this setup has over a spindle sander is that you can set the height of the drum to utilize the entire sanding surface. All you need is a piece of plywood with a cutout sized for the sanding drum you’re using. Swing the table off to one side and clamp the sanding platform into place.

Family Handyman

14 / 14

Drill evenly spaced holes

One of many ways to drill evenly spaced holes is to use a shelf standard attached to a fence. Tap a finish nail into the edge of your workpiece and clip off the head so that no more than 1/8 in. is left protruding. Mark your starting hole on the workpiece and drill it with the nail engaged in the shelf standard. Move the workpiece however many spaces are needed on the shelf standard for each consecutive hole. Next, check out our essential bandsaw tips and tricks you should know.

Every product is independently selected by our editors. If you buy something through our links, we may earn an affiliate commission.