Working With Round Duct Pipe

We talked to a long-time, expert "tin-bender" to learn the best methods and tips for working with round duct pipe

Man working with rolled duct pipe | Construction Pro Tips

We invited Bob Schmahl to give us a few pointers on working with round duct.. Bob’s been a tin bender for more than 40 years. He insists he still doesn’t know everything about ductwork, but we weren’t convinced. These tips should help make your next job run that much smoother.

1 / 12

Installing dampers at the end of a section of duct pipe | Construction Pro Tips

2 / 12

Install dampers at the registers

Adding heat runs in a basement may change the airflow in the rooms above. Each register should have its own damper that can be accessed for adjustment. If those dampers can’t be accessed from below, you’ll want to install them close enough to the register so that you can reach them through the register opening. Bob likes 4 x 10-in. boots (not shown)—you can easily fit your hand in them to adjust dampers, and there are more grate cover options for that size.

The end of a roll of flexible duct pipe | Construction Pro Tips

3 / 12

Bob's not a fan of flexible duct

There’s no question that flexible duct is easier to install than metal pipe, but consider this: Flexible duct can degrade over time. It collects dust and is almost impossible to clean. Flexible duct needs to be larger than pipes to allow the same amount of airflow. The most common problem Bob has seen: “People get careless and turn corners too sharp, which creates kinks that severely restrict airflow.” 

Screwing through old duct pipe tape | Construction Pro Tips

4 / 12

Don't peel off old tape

If you have to disassemble existing fittings, there’s no need to peel off the old foil tape first. Instead, just score the tape at the seam with a utility knife and remove the screws right through the tape. When it comes time to re-tape, just clean off the dust and apply new tape right over the old.

Rolling duct pipe together | Construction Pro Tips

5 / 12

Assemble the pipe like a zipper

When assembling pipe, start at one end and work the seam together like a zipper. Use one hand to keep the two edges close and the other to apply downward pressure. Use your leg, a workbench or the ground to support the back side of the pipe. If you make a mistake and have to dismantle a pipe, slam it down flat on the ground, seam side up. It should pop right apart.

A hole cutter cutting holes in a metal vent | Construction Pro Tips

6 / 12

A hole cutter works great in tight spots

Aviator snips work fine to cut holes in a trunk line, but only if there’s enough space. If you’re dealing with close quarters and you own a right-angle drill or attachment, you may want to invest in a sheet metal hole cutter. Otherwise you might have to take down the trunk line. You can buy them online for about $65. Malco is one manufacturer.

Caulking around take-offs | Construction Pro Tips

7 / 12

Caulk the take-offs

Caulk (don’t tape) the connection between the trunk line and a take-off (elbow) before you connect pipes to it. That way, you’ll be able to turn the take-off out of the way to caulk above it. Regular silicone is fine.

Overlapping butt joints with joint connectors | Construction Pro Tips

8 / 12

Overlap butt joints with draw band connectors

When you’re installing a pipe between two fixed parts, it’s impossible to slip in the piece using the crimped ends and still get the required 1-1/2-in. overlaps at both ends. Overlap one side as you normally would and create a butt joint on the other. Use a draw band connector to complete the butt joint. If your supplier doesn’t carry them, make your own by cutting a piece of pipe to overlap the ends, and then screw and tape the band into place. If you’re working with 6-in. pipe, you’ll need to use 7-in. pipe for the bands.

Applying tape to rolled duct pipe | Construction Pro Tips

9 / 12

Leave backing on the tape

If the ducts are going to be concealed, all seams need to be taped or caulked. Here’s Bob’s trick for taping a seam on a pipe that’s installed close to the subfloor: Cut a piece to length. Peel off part of the backing. Slide the backing up and over the pipe. Finally, pull down on the backing, which will pull the tape along with it. Inspectors will want to know you’ve used an approved tape, so buy the stuff with writing on it, or keep the roll on-site until inspection.

Cutting through duct pipe that has two marks on it | Construction Pro Tips

10 / 12

Make two marks for cutting

When cutting pipe, Bob likes to mark the size he needs on each side of the open seam with a marker. Flat metal is easier to cut than curved, so he uses his knee to support and flatten the pipe while he opens it up. Then you just sight on the far mark while you make the cut. It’ll be straight and perfect every time. Bob prefers snips made by Malco, which cost less than $35 at Amazon. Unless you enjoy trips to the ER, wear gloves when cutting pipe—the stuff is razor sharp.

11 / 12

Use support brackets and three screws

Each pipe needs support. You can use just about any support you want, but adjustable steel support brackets are quick and easy. And don’t forget to screw the pipe to the joist hanger so the pipes won’t rattle when someone stomps across the floor above. Every connection needs three screws. They don’t have to be evenly spaced. Use 1-in. galvanized zip screws designed for sheet metal.

Three uct pipe rings | Construction Pro Tips

12 / 12

Move one ring at a time

Figuring out the right combination of turns to get an elbow to point in the right direction can be perplexing. Bob recommends moving one “gore” (elbow ring) at a time, starting with the connected side. And don’t make 90-degree turns if you don’t have to. A 90-degree elbow creates the same resistance as adding 5 ft. of pipe.
Next, check out our guide to working with PVC conduit.

Disclosure: This post is brought to you by the Construction Pro Tips editors, who aim to highlight products and services you might find interesting. If you buy them, we get a small share of the revenue from the sale from our commerce partners. We frequently receive products free of charge from manufacturers to test. This does not drive our decision as to whether or not a product is featured or recommended. We welcome your feedback.