Tips for Tighter Miters and Better Coped Joints

New to construction? Want to brush up on your trim techniques? Check out this story.

A classic stained miter over a door | Construction Pro Tips
CONSTRUCTION PRO TIPS

1 / 6

Shim and shave miters

How many times have you set your miter saw exactly on 45 degrees and cut miters on a pair of moldings, only to discover they don’t fit? Well, don’t worry. There’s nothing wrong with your saw or your technique. Miters almost always have to be shaved to fit perfectly.

One method is to simply adjust the angle slightly on your miter saw and recut both moldings. The trouble is that making tiny adjustments to the cutting angle is difficult on many saws. A quicker and easier method is to place a shim against the miter saw fence to slightly change the angle. Move the shim away from the blade for smaller adjustments and closer for larger ones, or vary the thickness of the shim. Remember, both pieces need the exact same cut to fit precisely.

Cutting a piece of trim with the saw set at 45 degrees | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 1. Micro-adjust a miter

Close a gap on the top of a miter by placing a skinny shim (1/16 in. or less) against the portion of the fence farthest from the blade. Slide the molding tight to the shim and against the fence near the blade. Hold it in this position while you make the cut. Caution: Keep your fingers at least 6 in. from the path of the blade.

Setting up a piece of trim to saw | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 2. Treat both sides the same

Trim the other half of the miter using the same technique. Use the same shim and place it the same distance from the blade. Drop the blade slowly through the wood to shave thin slices.

Stained miter on the other side of the door | Construction Pro Tips
CONSTRUCTION PRO TIPS

2 / 6

Tilt trim on inset jambs

Occasionally you’ll run into a door or window jamb that isn’t quite flush with the wall. On a protruding jamb, you can nail the trim to the jamb, slip a shim between the trim and the drywall, and then nail the trim to the wall. Caulk and paint will hide the gap.

An inset jamb demands a different approach. First remove enough drywall so the trim can span the jamb and wall without rocking (Photo 2). This solves half the problem. But even now a regular 45-degree miter won’t fit because the molding has to tilt down to meet the jamb. Correct this problem by tilting the trim on the bed of the miter box to match the angle at which it rests against the wall. Then make standard 45-degree miter cuts. Photo 1 shows how to determine the correct thickness for the shim used in Photo 3 to tilt the molding.

Using a square to cut shim to gap width | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 1. Custom-cut a shim

Cut a shim just thick enough to slip under a straightedge spanning the drywall corner. Use this shim to elevate the outside edge of your molding (Photo 3) before cutting it.

Cutting back drywall around door casing | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 2. Slice the drywall

Trim back the drywall with a sharp utility knife until the molding no longer rocks when it’s set in place against the jamb and drywall. Use a hammer to mash and flatten the drywall if necessary.

Using a shim to get the right angle on your cut | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 3. Tilt the trim with a shim

Raise the outside edge of the molding with the shim and cut the 45-degree miter. Repeat the process for the opposite miter.

 White trim on an inside corner | Construction Pro Tips
CONSTRUCTION PRO TIPS

3 / 6

Cope baseboard faster

Coping is better than mitering at inside corners. But on tall baseboards, cutting the long, straight section of the cope with a coping saw is difficult, and the cut is usually wavy. Instead, start the cope as usual (Photo 1). Then tip the molding upside down in the miter saw and saw straight down to the profiled section. Finally, complete the cope by sawing out the profile (Photo 3).

Using a miter saw to cut through baseboard | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 1. Start with a miter cut

As with any coped joint, begin by cutting a 45-degree miter on the baseboard. The miter cut provides a profile to guide your cope cut.

Coping base with a miter saw | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 2. Make the straight cut

Turn the mitered baseboard upside down. Adjust the angle to about 15 degrees and saw down along the straight section of the beveled cut. Keep the blade slightly to the outside of the line. Let the blade stop before lifting it from the cut.

Coping the extra wood from the back of a piece of trim | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 3. Cut the curves

Saw out the remaining profiled section with a coping saw. Tilt the saw to at least a 30-degree angle to create a back bevel for easier fitting.

Inside trim | Construction Pro Tips
CONSTRUCTION PRO TIPS

4 / 6

Close gaps at inside corners

Uneven walls or floors that are out of level can cause even perfectly coped inside corners to look lousy. Check the fit of your cope before you fasten either base molding. That way you’ll still have the option to shim out the bottom of the square-cut (uncoped) piece to close a gap at the bottom of the cope (Photo 2). Photo 3 shows marking a cope that’s open at the top. You then file or plane to the line.

Checking the fit of a piece of base | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 1. Check the fit

Check the fit against the square-cut piece of base before nailing either of the two baseboards. The straight sections rarely fit perfectly.

Adding a screw behind a piece of base | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 2. Add a screw

Close a gap at the bottom by removing the square-cut base and driving a drywall screw into the wall about 1/2 in. from the floor. Test the cope and adjust the screw in or out until the cope fits tight.

Scribing a line across a piece of base | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 3. Scribe and trim

Close a gap at the top by scribing the gap with a small compass to mark the wood to be removed. Then file to the line.

Outside corner base and trim | Construction Pro Tips
CONSTRUCTION PRO TIPS

5 / 6

Overcut outside corners

Getting outside corners to fit tight is trickier than it looks. The key is to make accurate marks with the baseboard in place rather than relying on measurements. And then cut the piece a little long so you still have the option to shave a little from the angle if it doesn’t fit. Since gaps on the back (wall side) of the corner are barely noticeable, while gaps on the front (room side) are glaring, it’s a good idea to start by cutting slightly steeper 45-1/2-degree angles first. Then if there’s still a gap in the front, cut a slightly steeper angle on both pieces. You’ll need a compound miter saw or sliding compound miter saw to easily cut tight-fitting miters on wide baseboard.

Marking a piece of trim with a utility knife | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 1. Mark with a knife

Mark outside corners with a sharp utility knife. It’s far more precise than a pencil mark. Repeat the marking process on the opposite baseboard. Cut 45-1/2-degree angles on both boards, leaving each an extra 1/8 in. long.

Checking the fit of a miter before installation | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 2. Check the fit

If the miter is open on the front, increase the cutting angle to about 46 degrees and recut both sides. Be careful to remove only a hair’s width from each board. Reduce the angle if the cut is open at the back. When the angle is correct, recut each board just to the outside of the marks before nailing them into place.

The end of a piece of bottom window trim | Construction Pro Tips
CONSTRUCTION PRO TIPS

6 / 6

Make dead ends look good

When trim comes to a dead end—on window aprons or chair rail, for example—some trim carpenters just chop it off and nail it up. But there's a better way: Add a mitered "return" for a finished look.

Leaving the cut incomplete when coping | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 1. Leave the cut incomplete

Cut the angle for a small mitered return on your miter saw, but don’t completely cut it off from the trim stock. Instead, cut through the remaining sliver of wood with a utility knife. That way there will be no tear-out and the tiny piece won't get launched across the room.

Gluing the cap piece onto the end of a trim joint | Construction Pro Tips
CONSTRUCTION PRO TIPS

Step 2. Glue in the return

Choose a fast-acting cyanoacrylate glue like Krazy Glue formulated for wood.