Tips of the Trades Vol. 4

1 / 14

CPT sends out a big thanks to these folks who are willing to help out their fellow brothers and sisters in arms by sharing these brilliant nuggets of wisdom they picked up along the way.

 

Tape the end of the blade

2 / 14

Prevent cutting too deep

When I use my OMT to cut drywall, I tape the end of the blade off at 1/2” to make sure I don’t nick a pipe or wire immediately behind the drywall. Not that I’ve ever done that before...

Submitted by David Scott Clark (@baristabuildingcompany)

A post shared by Brad Near (@knarlycarl) on Nov 20, 2017 at 6:19pm PST

3 / 14

Be ready for auto repairs

I always carry tire plugs on all the work vehicles, just never know. A full day of work can be derailed if you lose your transportation.

Submitted by Brad Near (@knarlycarl)

Ultimate Prying Method

4 / 14

It's all about leverage

Had to use the ol’ '3-ft. crowbar on the end of thes 24’s'.

Submitted by (@plumbingfail)

A post shared by Brad Near (@knarlycarl) on Nov 19, 2017 at 3:29pm PST

5 / 14

Quick-release knot

I've used this knot for many years. An elderly friend who has since passed taught it to me. I can't remember what it's called, but it’s super handy! It works with rope or strap, doesn't come loose if it loses tension, and it's so easy to undo when finished. I've pulled countless vehicles out of the snow, lowered items from a roof, pulled things through chases, etc...

Submitted by Brad Near (@knarlycarl)

Spray your seals

6 / 14

Keep seals as good as new

We've had some people asking what we use to keep our automatic taping tools nice and lubricated. We recommend using a silicone spray on your seals and any moving parts. This helps keep everything moving smoothly and prevents your seals from drying up. This is a WD-40 brand of Silicone spray. Make sure to not use light lubricants like standard WD-40 because they will cause the seals to harden.

Submitted by @drywallnation

 

A post shared by ▫Dettmore Home Improvements▫ (@dettmore101) on Nov 16, 2017 at 2:51pm PST

7 / 14

 

A raised fence or stop block helps insure that sawdust won't hold the workpiece out of position. It's a simple but useful trick we employ to keep our parts consistent.

Submitted by Zach Dettmore (@dettmore101)

Reversed Blade for Vinyl

8 / 14

Cut vinyl without cracking

For part of today I had to add in a few pieces of siding that were blown off. Not sure how many of you do this yourselves, or know of this, but this is my way to cut vinyl siding when I don't have a vinyl blade on me. I turn a fine tooth blade backwards and cut like I normally would; if the vinyl is older you may get some mild chipping, but for the most part the blade just melts right through.

Submitted by Tyler Holmes (@holmesimprovement)

A post shared by Primetime Painting (@primetimepaintingcny) on Nov 15, 2017 at 1:58pm PST

9 / 14

Scrap metal guard

When we're tight on space and gotta make the bristles bend we make a guard outta scrap metal.

Submitted by Primetime Painting (@primetimepaintingcny)

Project Plumb line

10 / 14

Project a plumb line

If you are framing a wall up to a slope of unknown pitch. If you are using a laser to help with layout, try projecting a plumb line along your plates and then use your speed square on the pivot point to find your angle. This is a great way to get an accurate bevel or miter for the studs that lay into the plate on the slope.

Submitted by Aaron Thomas (@aaronthomasaquinas)

A post shared by Rural Renovators (@rrbuildings) on Jul 18, 2017 at 9:44am PDT

11 / 14

Story pole explanation

I know, most guys are going to know what a story pole is. Probably one of the oldest and most efficient tricks in the book when it comes to repetitive marking. But here's a video anyway, in case you don't know or need something cleared up. We use it on every job to ensure consistent marks across our entire project. As long as we get an accurate reading from our laser....the rest will be perfect.

Submited by Kyle Stumpenhorst (@rrbuildings)

 

Plug with wood screw

12 / 14

Put a screw in it

The other day I saw someone spending a considerable amount of time cleaning out the straw on a can of foam insulation, and I just had to say something! There's a super easy way to save these cans for a second use..put a wood screw in it! Seals it right up!

Submitted by Jeremy Dibos (@bloodsweatandsplinters)

Exact Fence Height

13 / 14

Fence Height Method

This is my method for determining the exact height on the miter saw fence to cut crown molding in the nested position.

Submitted by Modern Oak Construction (@modern_oak)

Contribute

14 / 14

We'd Love to Hear From You

Do you have a jobsite or tool tip that makes your work-life easier, safer, or just more fun?  Why not share it with your construction comrades? Plus, you can show off your professional prowess to your family and friends.

Click the image below to send us your Pro Tips! Please include an image if you can. We will contact you if we run your submission on the site.