Vinyl Siding Tips
Vinyl has long been a popular choice for both new construction and re-siding projects, and for good reason: It costs much less than metal, brick, fiber cement, stucco or wood. It allows a house to breathe, it doesn’t require painting, and it’s light and easy to work with. Here are some tips I learned as a siding contractor to help make your next vinyl siding installation quick, easy and effective.
Use the wider starter strip
The bottom of the starter strip (the part the bottom panel hooks on to) should be at least 1 in. below the top of the foundation, but the lower the siding is installed, the better. It protects the sheathing from rain, snow and pests. Most suppliers sell two sizes of starter, 2-1/2 in. and 3-1/2 in. Spend the extra few bucks on the wider stuff and start your siding a bit lower.
Cap the corner posts
Mice, bees and all sorts of other critters love making their home inside vinyl corner posts. Keep these pests out by capping each post before you install it. Start by cutting off a few inches of the J-channel portion on the post. Fold back the remaining flaps and gently tap a crease into them with your hammer. Notch the flaps so the post will fit snug up against the wall. The posts will crack if they’re not warm, so if it’s cold outside, lay them in the sun or bring them into the house before you do this. Caulk the remaining gaps when the post is installed.
Pull up as you nail
Most vinyl siding failures are caused when panels unlock from each other. Once this happens, it’s only a matter of time before the wind catches them and sends them flying into the neighbor’s yard. I always apply a little upward pressure as I nail each piece; this keeps the panels locked together nice and tight. Don’t “power-lift” each piece or you’ll put too much pressure on the nailing flange, causing it to break.
Flash the bottom of windows
Cut a piece of flashing out of felt paper and install it at the bottom corners of the windows before you install the side J-channels. Overlap the flashing onto the row of siding just below the window. Now, any water that runs inside the J-channels will come out on top of the siding and out the weep holes designed for this purpose.
Buy a vinyl siding blade
Pushing through vinyl siding with a wood blade in your circular saw will cause the siding to shatter, which is both frustrating and dangerous. Buy a blade made to cut vinyl siding. This one from Irwin cost about $10 at a home center. If you’re using a sliding miter saw or cut table like this one, and the siding is still chipping, try slowly pulling the saw backward through the siding.
Install longer panels first
When installing siding on each side of a window or door, start on the side that requires the longer panels. Longer siding panels don’t stretch as readily as smaller ones, so they’re not as easy to adjust if they get out of whack. Before nailing the last couple of pieces on the small side, measure up to the top of the window to make sure both sides are at the same height.
Don’t trap water behind corners
Corner posts above the roofline are a notorious source of water infiltration. If a corner post is installed tight to the shingles and the J-channel dead-ends into it, any water that runs down the J-channel will back up at the post and may find its way into the house. Instead, hold the corner post up a bit and run the J-channel beneath it.
Install kick-out flashing
Kick-out flashing prevents water from running down a roof and ending up behind the siding on an adjacent wall. It can be a pain to side around it, but you will fail your inspection if the inspector doesn’t see it on your job. Leave the kick-out flashing loose and slide the first panel behind the flashing. Then nail the flashing to the wall and lap the next piece over it. You may need a small trim nail to hold the siding seam tight (a little dab of caulk over the trim nail is a good idea).
Crimp and caulk the top course
Pay close attention to the area where the top row of siding meets the soffits. The most common approach here is to install sill trim at the soffits, rip down the top course of siding, and crimp the siding so the sill trim holds it in place. This works fine most of the time, but I always add a few blobs of caulking inside the bottom lip of the top course for extra security. You can crimp the siding using a Malco Snap Lock Punch, which costs $18 at Home Depot.
We’d Love to Hear From You
Do you have a jobsite or tool tip that makes your work-life easier, safer, or just more fun? Why not share it with your construction comrades? Plus, you can show off your professional prowess to your family and friends.
Click the image below to send us your Pro Tips! Please include an image if you can. We will contact you if we run your submission on the site.